Ecet345 signals and systems class class room activity #11 rlc

DeVry University

ECET345 Signals and Systems

Name of Student

Class Room Activity #11

RLC Impulse and Step Response


Objective of the lab experiment:

The objective of this experiment is to experimentally measure the step response of an RLC circuit and compare it to the response predicted using MATLAB.

Equipment list:

·         One LM741 op amp

·         One 1 resistor

·         One 100 resistor

·         One 1 k resistor

·         One 0.1 µF capacitor

·         One 10 mH inductor

·         One1 NI Elvis II board

·         Power supply with +15 V and -15 V outputs

·         Function generator capable of producing unipolar and bipolar square waves and sinusoids up to 5 KHz

·         Oscilloscope

·         Three BNC to alligator

·         One PC running LabVIEW 2010 or higher and CodeWarrior 5.9

·         MATLAB

·         One 2.0 mm flathead screwdriver


The previous labs have focused on having a single reactive component in a circuit to create a filter. This lab will focus on what happens if there are two different reactive components in the same circuit. An RLC circuit with two reactive components (an L and a C) is shown below. Using the knowledge gained previously, the transfer function can easily be found.

Note that all of the components are connected in series and the voltage across the resistor is our output.

Using the voltage divider rule here gives the following relationship:

Now substitute numerical values of R, L, and C. Then simplify the expression to get the transfer function as a ratio of two rational polynomials in s domain. Make the coefficient of the highest power of s unity in both numerator and denominator. If necessary, multiply the whole transfer function by a constant number.

Now write a MATLAB program that takes in the numerical values of R, L, and C; generates the transfer function of the system; and computes its Bode plot, its pole-zero map, and the step response of the system. Use the MATLAB keywords tf, bode, pzmap, and step to get these results.

Note that on the pole-zero map created by the pzmap command, poles are identified with an X and zeroes are identified with an O.

You should see a Bode plot as shown below for R = 100, L = 10 mH, and C = 0.1 µF.

Graph produced by MATLAB Bode plot command

Check the pole-zero map to see if it agrees with the poles and zeroes of the transfer function that was created by calculating the poles and zeroes manually.This kind of step response you will see is known as a decaying sinusoid, which can only appear in a second-order (or higher order) transfer function.

Compare the theoretical step response generated by MATLAB to the actual step response measured with the constructed circuit.


Step 1

Set up the frequency generator with the specifications below.


5 V


200 Hz

Signal Type

Square wave

Step 2

Build the following RLC circuit and observe the step response on the oscilloscope.

The observed response should look like the following:

Response of the 1 circuit as seen on an oscilloscope.



Step 3

Input these values into MATLAB using the supplied program and observe the theoretical step response.

Step 4

Change resistor to 1 kΩ and observe the step response. Then use the MATLAB code to observe the theoretical step response.

The observed response should look like the following:

Response of the 1 k circuit as seen on an oscilloscope




Step 5

Change resistor to 100 Ω and observe the step response. Then use the MATLAB code to observe the theoretical step response.

The observed response should look like the following:

Response of the 100 circuit as seen on an oscilloscope






Now answer the following questions.

1.       Does the step response from the actual measurement match the theoretical curve from MATLAB for R = 1 ? Note the magnitude of the peak value of the step response produced by MATLAB and compare it to the peak value produced by the experimentally measured curve. Why is the MATLAB value much higher than the experimental value? (Hint: The inductor is not an ideal inductor.)





2.       What is the mathematical relationship between the impulse and step response of a system?


3.       How will the shape of the step response change as the value of resistance is increased?


4.       Why is it desirable to include an op-amp buffer to drive the RLC circuit rather than driving the circuit directly from the function generator?






5.       Why is it that we never see an oscillatory response in an RC circuit, whose response is always exponential regardless of resistance?






Calculate the price of your order

550 words
We'll send you the first draft for approval by September 11, 2018 at 10:52 AM
Total price:
The price is based on these factors:
Academic level
Number of pages
Basic features
  • Free title page and bibliography
  • Unlimited revisions
  • Plagiarism-free guarantee
  • Money-back guarantee
  • 24/7 support
On-demand options
  • Writer’s samples
  • Part-by-part delivery
  • Overnight delivery
  • Copies of used sources
  • Expert Proofreading
Paper format
  • 275 words per page
  • 12 pt Arial/Times New Roman
  • Double line spacing
  • Any citation style (APA, MLA, Chicago/Turabian, Harvard)

Our guarantees

Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.

Money-back guarantee

You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.

Read more

Zero-plagiarism guarantee

Each paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.

Read more

Free-revision policy

Thanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.

Read more

Privacy policy

Your email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.

Read more

Fair-cooperation guarantee

By sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.

Read more